Short answer. Fascia wrap in Dallas means bending aluminum coil to cover the wood boards along the roof edge, so the paint stops peeling in the summer sun. We wrap only sound wood; soft boards get replaced first. On most homes we wrap the fascia when the gutters are already coming down, which saves a second setup.
What wrapping does for a roof edge
Fascia is the board the gutter hangs on. Painted wood looks fine for a few summers, then the paint chalks and peels, usually first on the south and west sides. Aluminum coil bent to the board's shape takes that weathering instead and does not need paint.
Wrap is a cover, not a cure. Water trapped behind a wrap rots the wood unseen, so the roof edge and gutter have to send water into the trough. That is why we check the drip edge and the gutter's pitch before any coil goes on.
Wrap, paint or replace the fascia?
| Paint the wood | Aluminum wrap | Replace the board | |
|---|---|---|---|
| When it fits | Sound wood, decorative profiles | Sound plain boards | Soft or split wood |
| Upkeep afterward | Repaint every few years | Rinse when you wash the house | Paint or wrap the new board |
| Hides problems? | No, peeling shows early | Can, so we check first | Fixes the problem |
| Good time to do it | Any dry spell | When gutters come down | Before new gutters go up |
What decides the cost of fascia wrap
We have no sourced Dallas range for wrap alone, so these are the factors that set your price.
- 1Linear footage
Total length of fascia to be wrapped.
- 2Board condition
Any rot gets replaced before wrapping.
- 3Corners and returns
Each corner and gable return takes extra bending.
- 4Height
Second-story eaves need more ladder setup.
- 5Gutters on or off
Wrapping while gutters are already down saves a setup.
Wrapping sound wood
We probe every board with an awl before wrapping. Firm wood gets a clean surface, a check for loose nails, and then coil bent on a brake to fit its face and bottom edge. The coil is fastened with color-matched trim nails along the bottom lip, where they are least visible. If a board is soft, it is replaced first through fascia board repair and then wrapped like the rest.
Color to match gutters
Fascia coil comes in the same colors as gutter coil, so the roof edge and gutters can read as one band of color. White and almond are the common picks in Dallas, with darker browns and bronze on brick homes that want the trim to recede. We bring samples, since color charts look different in Texas sun.
Bends at corners
Corners are where a cheap wrap job shows. Outside corners need a folded tab that laps over the next piece; inside corners need a clean relief cut so the coil does not buckle. We bend these on site so each one fits its corner rather than forcing a standard piece.
When not to wrap
Some homes are better off painted. Historic houses in a conservation district may face rules about changing exterior materials, decorative fascia with molding profiles does not wrap well, and boards with active rot need replacing either way. We will tell you if your house falls into one of these groups before you spend money on coil.
What a wrap job includes
- An awl check of every board
- Replacing soft sections before coil goes on
- Coil bent on site to each board's profile
- Folded tabs at outside corners
- Color-matched trim nails along the bottom lip
- Gutters rehung and sealed if they came down
- Clean-up of offcuts and old nails
Why Dallas fascia paint fails
Dallas July highs average close to 96 degrees, and the boards behind a gutter on a south or west wall take that sun every afternoon of the summer. Paint on that wood dries, chalks and lifts sooner than paint elsewhere on the house, and a gutter pressed against it hides the failure until the wood behind is wet. Aluminum coil does not peel, which is why wrapping pays off fastest on the sunny sides of a Dallas home.
How a fascia wrap goes
Inspect the boards
We probe every board and note any rot.
Gutters down if needed
If gutters are in the way, they come down carefully.
Fix and prep
Soft boards are replaced, loose nails reset.
Bend and fasten
Coil is bent on site and fastened along the lip.
Rehang and test
Gutters go back up, and we run water to check them.
Fascia wrap questions
Not without replacing the rotted part first. Wrapping over rot hides it while it keeps spreading.
Only if water is getting behind it. We check the drip edge and gutter so water goes into the trough.
The same range as gutter coil, so trim and gutters can match. We bring samples.
Painting costs less today, but in Dallas sun it needs redoing every few years. Wrap avoids that.
Sometimes, but it is cleaner with them off. We plan it with your gutter work when we can.
We repair and replace soffit panels. See soffit repair for that work.